Concrete is commonly used in every construction sites whether in buildings, bridges or even roads. Even though most people consider it a simple task, concrete cutting Edmonton demands a lot of caution in the processes. The worker should know that dust involved can affect his lungs and eyes. It can also corrode the finished surfaces.
For this reason the first consideration should be how to control dust produced when working on stones. It does not matter the type of tool employed to cut it, dust that comes out should not be inhaled. A common method that people have used to control this dust as they work on concrete is through wet cutting.
In this method, dust is collected inside cooling water. The dust is directed to the cooling water and allowed to settle there. This way, it does not fill the air, and become a risk to workers. Another method involves the use of pneumatic devices which help to draw dust into a stream of air. The dust is channeled slowly to a special place.
If you have diamond blades or using abrasive tools, water is needed to act as lubricant and for cooling the tools. The main challenge involved is that water will spill all over the work environment. This means you have to provide a drainage mechanism for this water. A vacuum system can also be used to control the spillage of water.
If you have electric tools, it is important to make sure that proper insulation is done. Effective ground fault insulation for protection must also be done. You cannot risk standing on wet surfaces when operating electric tools unless adequate protection is provided.
When using core drills, extra care is needed to make sure that no injury is sustained. Lack of proper base balance providing the machine with stable support may be the main cause of injury. The base suction is normally intended to provide this kind of support. Usually, the friction between the floor and the base should provide resistance to rotation. High speed rotation can injure the operator if the machine slips.
Relying on the vacuum as the main support to the drill base can be a big mistake since this may be hard to control in case of failure. The base might rotate at high speed and cut the operator. For it to have firm rest on the floor, a heavy object can be used to provide anchorage to the base. Most of these machines have a place where such support can be added with a heave stone or weight to hold it in position.
It is also important to consider what may be hidden inside concrete, if you want to cut. There could be stones or even metallic bar inside. Such things can bend machine blade or even break it. This is also true when drilling a hole. Concrete cutting Edmonton experts should use sharp tools and good quality equipment. Apart from that, properly trained operator must prepare himself with sufficient cooling water before embarking on this task.
For this reason the first consideration should be how to control dust produced when working on stones. It does not matter the type of tool employed to cut it, dust that comes out should not be inhaled. A common method that people have used to control this dust as they work on concrete is through wet cutting.
In this method, dust is collected inside cooling water. The dust is directed to the cooling water and allowed to settle there. This way, it does not fill the air, and become a risk to workers. Another method involves the use of pneumatic devices which help to draw dust into a stream of air. The dust is channeled slowly to a special place.
If you have diamond blades or using abrasive tools, water is needed to act as lubricant and for cooling the tools. The main challenge involved is that water will spill all over the work environment. This means you have to provide a drainage mechanism for this water. A vacuum system can also be used to control the spillage of water.
If you have electric tools, it is important to make sure that proper insulation is done. Effective ground fault insulation for protection must also be done. You cannot risk standing on wet surfaces when operating electric tools unless adequate protection is provided.
When using core drills, extra care is needed to make sure that no injury is sustained. Lack of proper base balance providing the machine with stable support may be the main cause of injury. The base suction is normally intended to provide this kind of support. Usually, the friction between the floor and the base should provide resistance to rotation. High speed rotation can injure the operator if the machine slips.
Relying on the vacuum as the main support to the drill base can be a big mistake since this may be hard to control in case of failure. The base might rotate at high speed and cut the operator. For it to have firm rest on the floor, a heavy object can be used to provide anchorage to the base. Most of these machines have a place where such support can be added with a heave stone or weight to hold it in position.
It is also important to consider what may be hidden inside concrete, if you want to cut. There could be stones or even metallic bar inside. Such things can bend machine blade or even break it. This is also true when drilling a hole. Concrete cutting Edmonton experts should use sharp tools and good quality equipment. Apart from that, properly trained operator must prepare himself with sufficient cooling water before embarking on this task.
About the Author:
You can visit the website www.edmontonconcretecutting.com for more helpful information about Safety Measures That Concrete Cutting Edmonton Experts Must Observe
0 comments:
Post a Comment