Natural disaster like hurricane and storm causes a lot of damage to property especially those without shutters. These shutters are important for protecting the houses during this time and they are fixed on the windows. Plywood is the most recommended materials and professionals offering board up services Texas use it in their work.
This work should always be done by two people and especially when large panels are to be used. It is important to carry out such work before the wind starts to blow. Such windy situations give technicians working on the windows a hard time in handling their materials. Adopting the following process will ensure a good outcome.
The first step is to mark where you will fix the studs and the places to be marked should be near the window. If you do not have nail heads in position of the studs, you can use a drill. It is important to ensure that the plywood is set in the right way because an improper move can easily cause it to fly.
When cutting the panels, some considerations should be made to allow an extension of about 1 inch on all sides of the frame. At this stage, you could be forced to label your panels in relation to the opening they are designed to cover. It could be necessary to use arrows to on the panels indicating the side that is meant to face up or down for easy identification during fitting.
The screws used should be of good quality to be able to resist corrosion and should be long enough to reach at least 2inches into the frame. Most professionals like using them because they hold tight and are easy to remove as well. It is important to insist in the use of galvanized pan-heads, lags because they are flat bottomed which prevents them from sinking and letting the plywood loose. The plywood should then be placed on the opening and then you should drill holes at intervals of 16 inches apart. The space between the panel edges to the hole should not be less than 1 inch.
If you are living in areas where hurricane happens a lot, you can screw hanger bolts in the frame to reach the wood by making corresponding holes with the drill. After drilling the holes, you can put the panel fast by use of washers and nuts when an emergency occurs. If the panels are used properly, they could serve another purpose when there is no danger of a natural disaster.
One can fix the plywood into the window opening using barrel bolts of about 4 inches which should be 16 inches part in a masonry case. However, care should be taken to enable you to see any kind of threat so you can be ready to handle it. Every step during this work may seem simple but should be taken seriously because it contributes to making the work a success.
Board up services Texas should at all times be entrusted with a company with a good reputation. Such a firm will always ensure you have the much needed protection at a cheap bargain. One should always ensure that the company to be contracted is licensed to carry out such type of work.
This work should always be done by two people and especially when large panels are to be used. It is important to carry out such work before the wind starts to blow. Such windy situations give technicians working on the windows a hard time in handling their materials. Adopting the following process will ensure a good outcome.
The first step is to mark where you will fix the studs and the places to be marked should be near the window. If you do not have nail heads in position of the studs, you can use a drill. It is important to ensure that the plywood is set in the right way because an improper move can easily cause it to fly.
When cutting the panels, some considerations should be made to allow an extension of about 1 inch on all sides of the frame. At this stage, you could be forced to label your panels in relation to the opening they are designed to cover. It could be necessary to use arrows to on the panels indicating the side that is meant to face up or down for easy identification during fitting.
The screws used should be of good quality to be able to resist corrosion and should be long enough to reach at least 2inches into the frame. Most professionals like using them because they hold tight and are easy to remove as well. It is important to insist in the use of galvanized pan-heads, lags because they are flat bottomed which prevents them from sinking and letting the plywood loose. The plywood should then be placed on the opening and then you should drill holes at intervals of 16 inches apart. The space between the panel edges to the hole should not be less than 1 inch.
If you are living in areas where hurricane happens a lot, you can screw hanger bolts in the frame to reach the wood by making corresponding holes with the drill. After drilling the holes, you can put the panel fast by use of washers and nuts when an emergency occurs. If the panels are used properly, they could serve another purpose when there is no danger of a natural disaster.
One can fix the plywood into the window opening using barrel bolts of about 4 inches which should be 16 inches part in a masonry case. However, care should be taken to enable you to see any kind of threat so you can be ready to handle it. Every step during this work may seem simple but should be taken seriously because it contributes to making the work a success.
Board up services Texas should at all times be entrusted with a company with a good reputation. Such a firm will always ensure you have the much needed protection at a cheap bargain. One should always ensure that the company to be contracted is licensed to carry out such type of work.
About the Author:
When you have the need for board up services Texas company is available and can be reached quickly via this link www.totalrestoration.com. To get a quote, click on the source http://www.totalrestoration.com.
0 comments:
Post a Comment